Planet Audio AC1500.1M ANARCHY 1500-watts Monoblock Class A/B 1 Channel 2 Ohm Stable Amplifier Reviews

Planet Audio AC1500.1M ANARCHY 1500-watts Monoblock Class A/B 1 Channel 2 Ohm Stable Amplifier

Planet Audio AC1500.1M ANARCHY 1500-watts Monoblock Class A/B 1 Channel 2 Ohm Stable Amplifier

  • Switchable Input Sensitivity: 100mV-2V or 2V-8V
  • Switchable Phase Shift (0-180º)
  • Selectable Bass Boost (0 to +18dB)
  • Continuously Variable Low Pass Crossover
  • Power and Protection LEDs

View larger
Class A/B Topology

A class A/B amplifier uses two groups of transistors and it is generally considered to be the best compromise of the two classes put together. A pure class ‘A’ amplifier typically has an enormous amount of current flowing through its output transistors with no audio signal. A pure class ‘B’ amplifier has no current flowing through its outputs with no audio signal. This eliminates virtually all of the crossover distortion that’s possible with class ‘B’ amplifiers. A class A/B amplifier is much more efficient than a class ‘A’ but without the possible distortion of a class ‘B’.

MOSFET PWM (Pulse Width Modulated) Power Supply

Metal–Oxide–Semiconductor Field-Effect Transistor is a transistor used for amplifying or switching electronic signals. We use it in our computers, telephones, game consoles, cars, electrical appliances and in this case, our amplifiers. They are found in systems where information is processed or stored. A MOSFET is basically an electrical switch that allows the flow of electrical current. An electrical switch has two possible states, on and off. This is where the MOSFET performs its most important role in our D Class amplifiers by allowing or preventing the flow of power and creating an efficient amplifier. The “Pulse Width Modulated” is a design that is significantly simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. The PWM can increase efficiency, is lighter, smaller, can reduce total cost, productivity and system reliability.

General Features
  • Thermal and Speaker Short Protection
  • 2 Ohm Stable Stereo Operation
  • Soft Turn-On Circuit
  • Remote Turn On / Turn Off Circuit
  • Variable Input Gain Control
  • Illuminated ANARCHY Logo
  • Black Anodized Heatsink
  • Chrome Plated RCA Low Level and High Level Inputs
  • LED Power and Protection Indicators

View larger

Low And High Level Inputs

The AC1500.1M has two different ways that you can get a signal into it. One is called Low level input and the other is called High level input. A low level input is measured in voltages. It comes in the form of RCA outputs from the back of your receiver and goes to the RCA inputs on your amplifier. A high level input is measure in wattages. It comes in the form one positive and one negative wire from the back of your receiver to and goes to the input terminal of your amplifier in the same wire form. Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect both the high level and low level inputs from your receiver to your amplifier at the same time.

Fixed High-Pass Crossover

Speakers also reproduce sound based on high, low or mid-range frequencies. High pass crossovers are geared specifically towards “highs” such as all size speakers, mid ranges and tweeters. Unlike the “Variable Low-Pass Crossover” mentioned above, you are not able to set exact sound specifications such as the bass, mid-range and high frequency reproduction. This High-Pass Crossover is fixed.

View larger

Variable Low-Pass Crossover

Subwoofers reproduce sound based on a number of different low-range frequencies. This process is called the crossover effect and occurs because the vast majority of audio systems cannot cover the entire spectrum sufficiently to minimize sound distortion and maintain an appropriate frequency ratio. In the case of our AC1500.1M amplifier, a variable crossover is offered so that you, the listener, can have the ability to set the frequency at which the crossover occurs, thereby setting specific sound specifications for the bass frequency reproduction.

Speaker, Battery, Remote and Ground Terminals + Fuses
View larger

View larger

Variable Bass Boost

So you have Bass Boost and Variable Bass Boost. The difference between the two is that with Bass Boost you either have extra bass or you don’t. But with Variable Bass Boost you have the control of exactly how much bass you want to pump out to your subwoofer(s). And this is what you get with the AC1500.1M Amplifier. Variable Bass Boost.

Remote Control
View larger

List Price: $ 157.00

Price: $ 157.00

Traffic Exchange Site
Translate »